Jump to content

Engines and Props

Discuss anything to do with Aircraft Engines and Props right here

1,554 topics in this forum

  1. Jabiru Gen 4 1 2 3 4 8

    By Bat6065,
    • 175 replies
    • 23.9k views

  2. Jabiru oil thermostat

    By Paul davenport,
    • 21 replies
    • 2.6k views

  3. LAME near Lethbridge, Victoria

    By Bat6065,
    • 2 replies
    • 804 views

  4. Dynamic Prop Balance 1 2

    By skippydiesel,
    • 37 replies
    • 2.9k views

  5. Exhaust Fabrication 1 2 3

    By skippydiesel,
    • 74 replies
    • 5.6k views

  6. The famously cool 912

    By danny_galaga,
    • 15 replies
    • 1.3k views

  7. Getting simplicity back into the Jabiru engine 1 2 3

    By Old Koreelah,
    • 52 replies
    • 6.2k views

  8. Move over ROTAX... 1 2 3 4

    By RFguy,
    • 87 replies
    • 7.9k views

  9. Loctite 574

    By Area-51,
    • 18 replies
    • 1.9k views

  10. Leak down tester for 912 Rotax

    By BillLipson,
    • 21 replies
    • 2.1k views
    • Kev
    • Kev

  11. Outboard Motors 1 2 3 4 5

    By skippydiesel,
    • 102 replies
    • 11.2k views

  12. Rotax 912 Movement 1 2 3 4

    By skippydiesel,
    • 82 replies
    • 7.8k views

  13. Rotax 912 80hp CHT/EGT sensors for engine monitor

    By Pat,
    • 3 replies
    • 1.2k views

  14. Approved engines and built-up areas 1 2 3

    By sfGnome,
    • 73 replies
    • 5.5k views

  15. Engine Installation Jabiru 2200 Gen 4

    By TexFlyer 1,
    • 0 replies
    • 1k views

  16. Excessive mag drop on Rotax 912ULS

    By rodgerc,   
    • 13 replies
    • 3k views

  17. A pre-owned Rotax 912 wanted

    By Safrony,
    • 0 replies
    • 865 views

  18. more data- PULP98 and AVGAS and det and vapour lock 1 2 3 4

    By RFguy,
    • 76 replies
    • 9.6k views

  19. Rotax 912 ULS, intermittent rough running during engine run up and in flight.

    By GDM,   
    • 9 replies
    • 2.7k views

  20. Looking for an Airmaster prop for a Jabiru 3300 to buy or borrow

    By TurbAero,
    • 13 replies
    • 1.7k views

  21. Engine selection (Rotax) 1 2

    By sfGnome,
    • 42 replies
    • 3.4k views

  22. Cleaning carbies/looking for blockages.. tips? 1 2 3 4

    By danny_galaga,
    • 87 replies
    • 7.5k views

  23. Curtis Valve Oil Drain Plug

    By BillLipson,
    • 11 replies
    • 1.5k views

  24. Rough running 914

    By rhtrudder,
    • 1 reply
    • 1.6k views

  25. 110 hp 4 cyl from Taiwan 1 2 3 4 5

    By danny_galaga,
    • 116 replies
    • 9.5k views
×
×
  • Create New...